RF-Max Digimax 210 Bedienungsanleitung PDF herunterladen (Seite 7)

Keene Electronics Catalogue 2005Tel 0870 990 9000 Fax 01332 830551 Web www.keene.co.uk

Tel 0870 990 9000 Fax 01332 830551 Web www.keene.co.uk

111

Remote controls Home automation Video tape

X10 PROFESSIONAL RANGE

The majority of X10 home automation products are designed to be

easy to install "plug and play" types that anyone can set-up and use.

There are however a few devices classed as "professional" because

they require installation by someone competent with domestic house

wiring. Given that they need a bit more difficult to fit, they do offer

an extra degree of flexibility. Classed as "DIN rail" products (because

they fit directly onto the DIN rail within most modern consumer units),

they can also be fitted into their own special housing adjacent to your

consumer unit.

AD10 DIN RAIL SWITCH

Basically a remote controlled relay, this can be directly

controlled either by switches (momentary or latching)

or by any other X10 controller. This makes it useful

for say hallway lighting applications, and also with its

16A load capability its great for items like immersion

heaters. Very useful.

[AD10] £34.99

LD10 (LD11) DIN RAIL DIMMER

These are designed to fit into a std DIN rail consumer

unit or similar enclosure and give you all the benefits

of X10 direct from the fusebox. The LD10 supports

on/off and dim/brighten. Additionally they support a

'soft start'. In effect when you operate your light

switch your lights will start from zero and gradually

brighten until they reach the last remembered level.

Then If you press and hold the light switch they will

gradually cycle through to maximum brightness and then back to dim.

Whenever you release the switch this sets the remembered level of

brightness for the next 'on' command. Very ease to install and use,

they can be controlled by any X10 controller and also by a momentary

action (non-latching) switch. Max load 60–700W.

[LD10] £34.99

DIN rail module enclosures

Ideal for housing the X10 DIN rail Appliance and Dimmer

modules; these are ideal if you’re tight for space within

your existing consumer unit, or you wish to site them

elsewhere.

INTERNAL ENCLOSURE for 3 standard size DIN modules,

or 1 LD10 or AD10. Enclosure features a hinged clear lid.

DIN rail length 100mm, overall dimensions 157 x 70 x

64mm.

[DRE3] £6.99

INTERNAL/EXTERNAL ENCLOSURE for up to 3 standard

size DIN modules, or 1 LD10 or AD10. Features hinged

clear lid with weatherproof seal. DIN rail length 100mm,

overall dimensions 131 x 73 x 91mm.

[DRE3E] £16.99

USING X10 WITH LOW VOLTAGE & ENERGY SAVING LIGHTING

There are a few important points to remember here

Low voltage lighting

12V halogen lighting systems usually use one of two different type of

transformer; a lightweight electronic (switch-mode) unit, or a heavier

conventional transformer. The heavy transformer type can be safely

operated and dimmed with an X10 module (LD10 or LM12U). The smaller

switch-mode type cannot be dimmed by X10 and it may result in damage

if you try. The only solution (if you require X10 dimming) is to change the

transformer for a conventional type. If you only require on/off control

without the dimming option then an AD10, AW10 or AM12U will be fine.

X10 Product quick compatibility checklist

[LD10] DIN RAIL DIMMER: OK for conventional incandescent lights (60-

700W, and mains voltage halogen lights. Can also be used with low

voltage halogen provided the transformer is NOT switch-mode type.

Requires momentary action switch.

[AD10] DIN RAIL SWITCHER: OK for on/off control of almost any type

of light or appliance up to 3kW.

[AW10U] WALL APPLIANCE SWITCH: OK for on/off control of almost

any type of light or appliance up to 2kW. (requires neutral connection)

[LW10U] WALL LIGHT SWITCH: Replaces conventional light switch for

on/off and dim/brighten control. Cannot be used with energy saver type

lamps or low voltage halogen systems. Does not require a neutral

connection so will replace existing light switches easily. Minimum (yes

minimum!) rating 60W, max 300W

[LM12U] PLUG IN LAMP MODULE: On/off and dim/brighten control of

conventional lamps only (max 300W) - not for use with energy saver or

low voltage lighting.

[AM12U] PLUG IN APPLIANCE MODULE: OK for on/off control of

almost any type of light or appliance up to 13A.

[LM15] BAYONET FIT X10 MODULE: For use with conventional (100W

max) filament bulbs only, not for use with energy saver or fluorescent

bulbs. Provides on/off only (not dimmable).

What on earth is an "inductive" or "resistive" load?

A resistive load is, as you'd expect, purely resistive and has nothing else

that affects its power requirements. For example appliances with resistive

loads include; toasters, electric fires, electric ovens, kettles, conventional

filament type lamps, etc.

In electrical terms an "inductor" is a number of turns of wire wrapped

around a core and "inductance" is the ability of this coil to store energy. It

follows that an inductive load is something which contains coils, usually

in the form of motors, solenoids or relays. Inductive loads usually require

more power when they first start up than they do to continue running. For

example, appliances with inductive loads include; power tools, washing

machines, spin dryers, high powered amplifiers, arc welders,

fridge/freezers and anything else likely to have lots of coils in it....

DIN rail filter

Can be used as a coupler, to allow X10 signals to be

passed between phases in a multi-phase

installation, and can also be used as a filter. In filter

mode it can be used to prevent X10 signals from

entering or leaving the building (in the case of

interference from a neighbour), or to filter a

specific load from the consumer unit. Suitable for

heavy duty loads up to 63A.

[FD10] £34.99

Universal relay module

Another interesting gadget, this unit

contains an X10 controlled beeper and a

pair of normally open isolated contacts.

It can be set to operate as a beeper only,

a contact relay only, or both. The

isolated contacts can be set for

momentary or sustained closure and can

switch up to 5A at 24v DC (30v AC at

5A). When set for momentary operation

the contacts, close and then open again

after about two seconds. In this mode, OFF commands are ignored. In

continuous mode it closes the contacts on receipt of an ON signal and

opens them again when it receives an OFF (or ALL OFF) signal. Think

of it as an X10 controlled heavy duty switch, ideal for use in electronic

projects eg door/window openers, watering systems, thermostats, etc.

[UM7206] £34.99

X10 addressable power supply

Plugs into a standard (UK) 240V 13A mains outlet,

provides an X10 on/off switchable DC power

supply (12V 100mA) via a 2m cable. The device is

intelligent in that it automatically switches off

whenever it detects an "on" command for any

other address on the same X10 circuit

[XM11U] £19.99

Also available as part of the XCAM2 wireless

video camera surveillance kits

X10 Siren

A very loud (105db) siren. Simply plug in and set to

the appropriate X10 address. Great for adding

security functions to items like the MS13E Hawkeye

sensor.

[PH7208] £54.99

X10 receivers (continued)

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

RF-Max Digimax 210 Bedienungsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Thermostate RF-Max Digimax 210